Description
TUNEL 1-Step In Situ Apoptosis Kit (FL594)
The TUNEL 1-Step In Situ Apoptosis Kit (FL594) (AKES073) detects DNA strand breaks in apoptotic cells in situ. Terminal deoxynucleotidyl transferase (TdT) labels exposed 3'-OH ends with FL594-labeled dUTP, and signal is read by fluorescence microscopy with a TRITC filter set. Researchers use the kit to localize apoptosis in tissue sections and cell preparations without gel-based analysis.
Apoptosis is a programmed cell death process in which specific DNA endonucleases are activated and cut genomic DNA between nucleosomes. This internucleosomal cleavage produces multimers of 180~200 bp fragments, corresponding to the oligonucleosomal size, which typically migrate as a ladder on an agarose gel. The cleavage leaves exposed 3'-OH ends on the broken DNA. The TUNEL 1-Step In Situ Apoptosis Kit (FL594) targets these exposed 3'-OH termini so that apoptotic cells can be identified directly in their cellular context.
Researchers use in situ detection of these DNA ends to localize apoptosis within intact tissue and cell preparations instead of in bulk extracts. The kit is described for paraffin sections, frozen sections, cell slides, and cell smears, which preserves morphology and places the signal in individual nuclei. Because the result is read by fluorescence microscopy, a single section or slide can be scored for the distribution of labeled cells. DAPI counterstaining is included as an optional step so that all nuclei can be visualized alongside the labeled cells. The sources do not name specific disease models.
In the labeling reaction, Terminal Deoxynucleotidyl Transferase (TdT) catalyzes the addition of fluorescein-labeled dUTP, here FL594, to the exposed 3'-OH ends. Samples are fixed in 4% paraformaldehyde and permeabilized with 0.2% Triton X-100 in PBS to allow reagent entry. Before labeling, samples are equilibrated with TdT Equilibration Buffer at 37 �C for 10~30 min. The labeling working solution is then applied at 50 �L per slide and incubated at 37 �C for 60 min with shading light in a humidified chamber. FL594 is detected at Ex/Em 590/617 nm with a TRITC filter set, and the total assay time is 3 hours.
Suitable sample types are cell slides, cell smears, paraffin sections, and frozen sections. Fixation is an important step, because unfixed cells may lose smaller DNA fragments and produce lower signals. Acidic fixatives and fixation with ethanol or methanol are reported to cause problems, and the sources recommend 4% paraformaldehyde. Samples must be kept moist throughout the procedure, since dry slides cause the experiment to fail. After labeling and washing, slides are sealed with an anti-fluorescence quenching mounting solution. The sources advise observing results as soon as possible, or storing slides at 4 �C protected from light.
| Product Name: | TUNEL 1-Step In Situ Apoptosis Kit (FL594) |
| SKU: | AKES073 |
| Application: | DNA Fragmentation Detection |
| Detection Method: | Fluorometric |
| Sample Types: | Paraffin section, frozen section, cell slide |
| Assay Time: | 3 hours |
| Detection Instrument: | Fluorescence microscope |
| Storage: | -20°C, protect from light |
| Expiration: | 12 months |
- One-step TdT labeling of exposed 3'-OH DNA ends with FL594-labeled dUTP
- Fluorometric readout: Ex/Em 590/617 nm, TRITC filter set
- Validated sample types: paraffin sections, frozen sections, and cell slides or smears
- Assay time of approximately 3 hours
- Includes DNase I positive-control workflow and DAPI nuclear counterstain option
- Research Use Only
The exposed 3'-OH ends of fragmented DNA are catalyzed by Terminal Deoxynucleotidyl Transferase (TdT) with FL594-labeled dUTP. Incorporated label is detected directly by fluorescence microscopy, with strong fluorescence in cells containing DNA strand breaks. Nuclei can be counterstained with DAPI.
- In situ detection of DNA fragmentation in apoptotic cells in paraffin-embedded tissue sections
- Apoptosis analysis in frozen tissue sections
- Apoptosis detection in cultured cell slides and cell smears, such as camptothecin-treated HeLa cells
- Co-localization of apoptotic DNA breaks with DAPI nuclear counterstain in tissue sections
| Component | Storage |
| TdT Equilibration Buffer | -20°C |
| TdT Enzyme | -20°C |
| Proteinase K (100×) | -20°C |
| Labeling Solution (FL594) | -20°C, protect from light |
| DNase I (20 U/µL) | -20°C |
| DNase I Buffer (10×) | -20°C |
| DAPI Reagent (25 µg/mL) | 2-8°C or -20°C, protect from light |
- 4% paraformaldehyde fixative (self-prepared in PBS)
- 0.2% Triton X-100 permeabilization buffer (self-prepared in PBS)
- PBS
- ddH2O
- Xylene (for paraffin sections)
- Ethanol at 100%, 95%, 90%, 80%, and 75% (for paraffin sections)
- Anti-fluorescence quenching mounting medium
- Fluorescence microscope with TRITC filter set
- 37°C incubator and humidified chamber
- Absorbent paper and filter paper
- Centrifuge capable of 600×g (for cell smears)
Cell slides and cell smears
- Wash cell slides with PBS for 1 time. For cell smears, collect the cells, resuspend in PBS, add an equal volume of fixative buffer, and fix at room temperature for 15~20 min or at 4 �C for 1~2 h. Centrifuge at 600 x g for 5 min, resuspend in PBS, spread 25~50 �L of cell suspension on slides, and dry.
- Immerse cell slides in fixative buffer (4% paraformaldehyde in PBS) at room temperature for 15~20 min, or at 4 �C for 1~2 h.
- Wash slides with PBS for 3 times, 5 min each.
- Permeabilize with Permeabilization Buffer (0.2% Triton X-100 in PBS). Prepare the 0.2% Triton X-100 solution fresh or store it at 4 �C for 1~2 days.
- Wash slides with PBS for 3 times, 5 min each.
Paraffin sections
- Deparaffinize in xylene twice, 10 min each time. If room temperature is below 20 �C, the dewaxing time can be extended to 20 min.
- Hydrate through a graded ethanol series of 100%, 95%, 90%, 80%, and 75%, 3 min per step.
- Wash slides with PBS for 2 times, 5 min each.
- Absorb moisture around the sample with filter paper. Add 100 �L of 1x Proteinase K working solution per sample (prepared by adding 1 �L Proteinase K (100x) to 99 �L PBS), and incubate at 37 �C for 20 min.
- Wash slides with PBS for 3 times, 5 min each.
Frozen sections
- Bring frozen sections to room temperature. Immerse slides in fixative buffer (4% paraformaldehyde in PBS) and incubate at room temperature (15~25 �C) for 30 min.
- Wash slides with PBS for 2 times, 5 min each.
- Incubate in Permeabilization Buffer (0.2% Triton X-100 in PBS) at 37 �C for 10 min.
- Wash slides with PBS for 3 times, 5 min each.
- Add 100 �L of 1x Proteinase K working solution to each sample and incubate at 37 �C for 10~20 min.
- Wash slides with PBS for 3 times, 5 min each.
Controls (apply to all sample types)
- Positive control: add 100 �L of 1x DNase I Buffer to each slide and incubate at room temperature for 5 min. Blot the liquid around the sample, add 100 �L DNase I working solution (200 U/mL) to each slide, and incubate at 37 �C for 10~30 min. Wash with PBS for 3 times, 5 min each, then label with the experimental group.
- Negative control: prepare as for the experimental group, but use the negative-control labeling mixture without TdT enzyme (35 �L TdT Equilibration Buffer and 10 �L labeling solution, 0 �L TdT enzyme). The DNase I pretreatment is optional for the negative control.
- Prepare 1x DNase I buffer by diluting DNase I Buffer (10x) with ddH2O. Prepare DNase I working solution (200 U/mL) by diluting DNase I (20 U/�L) with 1x DNase I buffer, and do not vortex the DNase I.
Reagent preparation
- Prepare 1× Proteinase K working solution by adding 1 µL Proteinase K (100×) to 99 µL PBS. Prepare fresh before use.
- Prepare 1× DNase I buffer by diluting DNase I buffer (10×) with ddH2O. Prepare fresh before use.
- Prepare DNase I working solution (200 U/mL) by diluting DNase I (20 U/µL) with 1× DNase I buffer. Mix gently; do not vortex.
- Prepare DAPI working solution by adding 4 µL DAPI (25×) to 96 µL PBS. Prepare fresh before use.
Sample preparation
- Cell slides: wash with PBS for 1 time, then immerse in 4% paraformaldehyde at room temperature for 15 to 20 min or at 4°C for 1 to 2 h.
- Cell smears: resuspend cells in PBS, add an equal volume of 4% paraformaldehyde, fix at room temperature for 15 to 20 min or at 4°C for 1 to 2 h, centrifuge at 600×g for 5 min, resuspend in PBS, spread 25 to 50 µL on slides, and dry.
- Paraffin sections: dewax in xylene twice for 10 min each, rehydrate through graded ethanol (100%, 95%, 90%, 80%, 75%, 3 min each), then fix in 4% paraformaldehyde.
- Frozen sections: equilibrate to room temperature, fix in 4% paraformaldehyde at room temperature (15 to 25°C) for 30 min, then wash with PBS 2 times for 5 min each.
- Permeabilize with 0.2% Triton X-100 in PBS at 37°C for 10 min (slides as applicable), then wash with PBS 3 times for 5 min each.
Positive and negative controls
- Positive control: add 100 µL of 1× DNase I buffer to the slide and incubate at room temperature for 5 min. Blot, add 100 µL DNase I working solution (200 U/mL), and incubate at 37°C for 10 to 30 min. Wash with PBS 3 times for 5 min each.
- Negative control: incubate with 1× DNase I buffer at 37°C for 10 to 30 min in place of DNase I, then wash with PBS 3 times for 5 min each.
- Tissue sections: Proteinase K treatment at 37°C for 10 to 20 min (cell slides: 20 min). Optimize incubation time for each tissue or species.
Labeling and counterstain
- Add 100 µL of TdT Equilibration Buffer to each sample and incubate at 37°C for 10 to 30 min. Blot the liquid around the sample without allowing it to dry.
- Prepare the labeling working solution per sample. Experimental group: 35 µL TdT Equilibration Buffer, 10 µL Labeling Solution, and 5 µL TdT Enzyme. Negative control: 40 µL TdT Equilibration Buffer and 10 µL Labeling Solution (no TdT Enzyme).
- Add 50 µL of labeling working solution to each sample and incubate at 37°C for 60 min in a humidified chamber, protected from light. Extend up to 4 h for weak signal in some systems.
- Wash with PBS 3 times for 5 min each. Blot, add DAPI working solution, and incubate at room temperature for 5 min protected from light. Wash with PBS 4 times for 5 min each.
- Blot around the sample, apply anti-fluorescence quenching mounting medium, and seal the slide. Analyze promptly under a fluorescence microscope with a TRITC filter set.
What sample types are compatible with this kit?
The kit is suitable for paraffin sections, frozen sections, cell slides, and cell smears. The sources note that the incubation time may differ between tissues or species, so a preliminary experiment is recommended to confirm it.
How should the kit and labeling reagents be stored?
The kit can be stored at -20 �C for 12 months, protected from light. TdT Enzyme must be stored strictly at -20 �C, and it should be returned to -20 �C immediately after use. Labeling solution should be stored in the dark, and slides should be stored at 4 �C protected from light if observation is delayed.
What should I do if staining is weak or background is high?
For high background, dilute TdT Equilibration Buffer 1:2 to 1:10 and control the enzyme concentration and reaction time. For weak signal, extend the labeling incubation, which may require up to 4 hours at 37 �C for some systems, or extend the permeabilization or dewaxing time.
Which instrument and filter set are used for readout?
Analyze samples directly under a fluorescence microscope. For FL594, use excitation/emission of 590/617 nm with a TRITC filter set. DAPI nuclear counterstain is detected at 350/470 nm with a DAPI filter set.
How long does the assay take?
The total assay time is 3 hours. The labeling step itself is 60 min at 37 �C in a humidified chamber with shading light.
What are the key points for avoiding failed experiments?
Keep samples moist throughout the procedure, and do not vortex the labeling solution or TdT enzyme; mix by gentle pipetting. Include positive and negative controls in each experiment. Avoid repeated freezing and thawing of the labeling solution and TdT enzyme, and wash thoroughly, as insufficient washing can reduce enzyme activity.




