Mouse CREB ELISA Kit (MOFI00745)

Product Name:	Mouse CREB ELISA Kit
Product Code:	MOFI00745
Size:	96 Assays
Alias:	CREB, Creb1, CREB, active transcription factor CREB, cAMP responsive element binding protein 1, cAMP-response element-binding protein-1, cAMP-responsive element-binding protein 1, CREB-1, MGC9284, transactivator protein
Detection Method:	Sandwich ELISA
Application:	This immunoassay kit allows for the in vitro quantitative determination of Mouse CREB concentrations in serum plasma and other biological fluids.
Sensitivity:	0.094ng/ml
Range:	0.156-10ng/ml
Storage:	4°C for 6 months
Note:	For Research Use Only

Recovery:

Matrices listed below were spiked with certain level of Mouse CREB and the recovery rates were calculated by comparing the measured value to the expected amount of Mouse CREB in samples.

Matrix	Recovery range(%)	Average(%)
serum(n=5)	94-105	99
EDTA plasma(n=5)	87-97	92
UFH plasma(n=5)	85-105	96

Linearity:

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Mouse CREB and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample	1:2	1:4	1:8
serum(n=5)	90-102%	85-103%	86-99%
EDTA plasma(n=5)	87-97%	84-101%	84-100%
UFH plasma(n=5)	85-99%	83-96%	81-97%

Intra Assay:

CV <8%

Inter Assay:

CV <10%

Component	Quantity	Storage
ELISA Microplate (Dismountable)	8-12 strips	4°C for 6 months
Lyophilized Standard	2	4°C/-20°C
Sample/Standard Dilution Buffer	20ml	4°C
Biotin-labeled Antibody(Concentrated)	120ul	4°C (Protect from light)
Antibody Dilution Buffer	10ml	4°C
HRP-Streptavidin Conjugate(SABC)	120ul	4°C (Protect from light)
SABC Dilution Buffer	10ml	4°C
TMB Substrate	10ml	4°C (Protect from light)
Stop Solution	10ml	4°C
Wash Buffer(25X)	30ml	4°C
Plate Sealer	5	-

Other materials and equipment required:

Microplate reader with 450 nm wavelength filter
Multichannel Pipette, Pipette, microcentrifuge tubes and disposable pipette tips
Incubator
Deionized or distilled water
Absorbent paper
Buffer resevoir

Uniprot

Q01147

UniProt Protein Function:	CREB: a transcription factor of the leucine zipper family of DNA binding proteins. Binds as a homodimer to the cAMP-responsive element (CRE). Phosphorylated by several protein kinases, and induces transcription of genes in response to hormonal stimulation of the cAMP pathway. Two splice-variant isoforms have been described.
UniProt Protein Details:	Protein type:Transcription factor; DNA-binding Chromosomal Location of Human Ortholog: 2q34 Cellular Component: nucleoplasm; nucleus Molecular Function:RNA polymerase II transcription factor activity, enhancer binding; protein binding; enzyme binding; transcription cofactor activity; transcription factor activity Biological Process: transcription from RNA polymerase II promoter; circadian rhythm; lactation; axon guidance; response to glucagon stimulus; viral reproduction; nerve growth factor receptor signaling pathway; positive regulation of osteoclast differentiation; positive regulation of transcription, DNA-dependent; stress-activated MAPK cascade; positive regulation of multicellular organism growth; toll-like receptor 3 signaling pathway; signal transduction; protein amino acid phosphorylation; toll-like receptor 10 signaling pathway; response to organic substance; toll-like receptor 5 signaling pathway; synaptic transmission; toll-like receptor 4 signaling pathway; response to drug; epidermal growth factor receptor signaling pathway; mitochondrion organization and biogenesis; Notch signaling pathway; fibroblast growth factor receptor signaling pathway; phosphoinositide-mediated signaling; protein stabilization; secretory granule organization and biogenesis; MyD88-independent toll-like receptor signaling pathway; organelle organization and biogenesis; positive regulation of hormone secretion; positive regulation of lipid biosynthetic process; memory; toll-like receptor 2 signaling pathway; MyD88-dependent toll-like receptor signaling pathway; phospholipase C activation; pituitary gland development; toll-like receptor signaling pathway; positive regulation of fat cell differentiation; innate immune response; positive regulation of transcription from RNA polymerase II promoter; toll-like receptor 9 signaling pathway; regulation of cell size Disease: Histiocytoma, Angiomatoid Fibrous
NCBI Summary:	This gene encodes a transcription factor that is a member of the leucine zipper family of DNA binding proteins. This protein binds as a homodimer to the cAMP-responsive element, an octameric palindrome. The protein is phosphorylated by several protein kinases, and induces transcription of genes in response to hormonal stimulation of the cAMP pathway. Alternate splicing of this gene results in several transcript variants encoding different isoforms. [provided by RefSeq, Mar 2016]
UniProt Code:	Q01147
NCBI GenInfo Identifier:	4758054
NCBI Gene ID:	1385
NCBI Accession:	NP_004370.1
UniProt Secondary Accession:	Q01147,Q01147,
UniProt Related Accession:	P16220
Molecular Weight:	Predicted Band Size: 37kDa
NCBI Full Name:	cyclic AMP-responsive element-binding protein 1 isoform A
NCBI Synonym Full Names:	cAMP responsive element binding protein 1
NCBI Official Symbol:	CREB1
NCBI Official Synonym Symbols:	CREB; CREB-1
NCBI Protein Information:	cyclic AMP-responsive element-binding protein 1
UniProt Protein Name:	Cyclic AMP-responsive element-binding protein 1
Protein Family:	CREB-binding protein
UniProt Gene Name:	CREB1
UniProt Entry Name:	CREB1_HUMAN

*Note: Protocols are specific to each batch/lot. For the correct instructions please follow the protocol included in your kit.

Step	Procedure
1.	Set standard, test sample and control (zero) wells on the pre-coated plate respectively, and then, record their positions. It is recommended to measure each standard and sample in duplicate. Wash plate 2 times before adding standard, sample and control (zero) wells!
2.	Aliquot 0.1ml standard solutions into the standard wells.
3.	Add 0.1 ml of Sample / Standard dilution buffer into the control (zero) well.
4.	Add 0.1 ml of properly diluted sample (Human serum, plasma, tissue homogenates and other biological fluids.) into test sample wells.
5.	Seal the plate with a cover and incubate at 37 °C for 90 min.
6.	Remove the cover and discard the plate content, clap the plate on the absorbent filter papers or other absorbent material. Do NOT let the wells completely dry at any time. Wash plate X2.
7.	Add 0.1 ml of Biotin- detection antibody working solution into the above wells (standard, test sample & zero wells). Add the solution at the bottom of each well without touching the side wall.
8.	Seal the plate with a cover and incubate at 37°C for 60 min.
9.	Remove the cover, and wash plate 3 times with Wash buffer. Let wash buffer rest in wells for 1 min between each wash.
10.	Add 0.1 ml of SABC working solution into each well, cover the plate and incubate at 37°C for 30 min.
11.	Remove the cover and wash plate 5 times with Wash buffer, and each time let the wash buffer stay in the wells for 1-2 min.
12.	Add 90 µL of TMB substrate into each well, cover the plate and incubate at 37°C in dark within 10-20 min. (Note: This incubation time is for reference use only, the optimal time should be determined by end user.) And the shades of blue can be seen in the first 3-4 wells (with most concentrated standard solutions), the other wells show no obvious color.
13.	Add 50 µL of Stop solution into each well and mix thoroughly. The color changes into yellow immediately.
14.	Read the O.D. absorbance at 450 nm in a microplate reader immediately after adding the stop solution.

When carrying out an ELISA assay it is important to prepare your samples in order to achieve the best possible results. Below we have a list of procedures for the preparation of samples for different sample types.

Sample Type	Protocol
Serum:	If using serum separator tubes, allow samples to clot for 30 minutes at room temperature. Centrifuge for 10 minutes at 1,000x g. Collect the serum fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles. If serum separator tubes are not being used, allow samples to clot overnight at 2-8°C. Centrifuge for 10 minutes at 1,000x g. Remove serum and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles.
Plasma:	Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples at 4°C for 15 mins at 1000 - g within 30 mins of collection. Collect the plasma fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles. Note: Over haemolysed samples are not suitable for use with this kit.
Urine & Cerebrospinal Fluid:	Collect the urine (mid-stream) in a sterile container, centrifuge for 20 mins at 2000-3000 rpm. Remove supernatant and assay immediately. If any precipitation is detected, repeat the centrifugation step. A similar protocol can be used for cerebrospinal fluid.
Cell culture supernatant:	Collect the cell culture media by pipette, followed by centrifugation at 4°C for 20 mins at 1500 rpm. Collect the clear supernatant and assay immediately.
Cell lysates:	Solubilize cells in lysis buffer and allow to sit on ice for 30 minutes. Centrifuge tubes at 14,000 x g for 5 minutes to remove insoluble material. Aliquot the supernatant into a new tube and discard the remaining whole cell extract. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20°C.
Tissue homogenates:	The preparation of tissue homogenates will vary depending upon tissue type. Rinse tissue with 1X PBS to remove excess blood & homogenize in 20ml of 1X PBS (including protease inhibitors) and store overnight at ≤ -20°C. Two freeze-thaw cycles are required to break the cell membranes. To further disrupt the cell membranes you can sonicate the samples. Centrifuge homogenates for 5 mins at 5000xg. Remove the supernatant and assay immediately or aliquot and store at -20°C or -80°C.
Tissue lysates:	Rinse tissue with PBS, cut into 1-2 mm pieces, and homogenize with a tissue homogenizer in PBS. Add an equal volume of RIPA buffer containing protease inhibitors and lyse tissues at room temperature for 30 minutes with gentle agitation. Centrifuge to remove debris. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20 °C.
Breast Milk:	Collect milk samples and centrifuge at 10,000 x g for 60 min at 4°C. Aliquot the supernatant and assay. For long term use, store samples at -80°C. Minimize freeze/thaw cycles.