Rat Angiopoietin 2/ANG2 ELISA Kit (RTFI00105)

Product Name:	Rat Angiopoietin 2/ANG2 ELISA Kit
Product Code:	RTFI00105
Size:	96 Assays
Target:	Rat ANG-2
Alias:	ANG-2, Angiopoietin 2, ANG-2, ANGPT2, AGPT2
Reactivity:	Rat
Detection Method:	Sandwich ELISA, Double Antibody
Sensitivity:	37.5pg/ml
Range:	62.5-4000pg/ml
Storage:	4°C for 6 months
Note:	For Research Use Only

Recovery:

Matrices listed below were spiked with certain level of Rat ANG-2 and the recovery rates were calculated by comparing the measured value to the expected amount of Rat ANG-2 in samples.

Matrix	Recovery range(%)	Average(%)
serum(n=5)	85-100	95
EDTA plasma(n=5)	94-101	97
UFH plasma(n=5)	90-104	94

Linearity:

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Rat ANG-2 and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample	1:2	1:4	1:8
serum(n=5)	88-102%	93-102%	95-103%
EDTA plasma(n=5)	86-100%	85-99%	82-100%
UFH plasma(n=5)	84-98%	80-100%	87-98%

Intra-Assay:

CV <8%

Inter-Assay:

CV <10%

Uniprot:

O35462

UniProt Protein Function:	ANGPT2: Binds to TEK/TIE2, competing for the ANGPT1 binding site, and modulating ANGPT1 signaling. Can induce tyrosine phosphorylation of TEK/TIE2 in the absence of ANGPT1. In the absence of angiogenic inducers, such as VEGF, ANGPT2-mediated loosening of cell-matrix contacts may induce endothelial cell apoptosis with consequent vascular regression. In concert with VEGF, it may facilitate endothelial cell migration and proliferation, thus serving as a permissive angiogenic signal. Interacts with TEK/TIE2, competing for the same binding site as ANGPT1. 3 isoforms of the human protein are produced by alternative splicing.
UniProt Protein Details:	Protein type:Secreted, signal peptide; Secreted Chromosomal Location of Human Ortholog: 8p23.1 Cellular Component: extracellular space; cell projection; extracellular region; plasma membrane; nucleus Molecular Function:protein binding; metal ion binding; receptor tyrosine kinase binding; receptor binding Biological Process: Tie receptor signaling pathway; organ regeneration; maternal process involved in pregnancy; negative regulation of blood vessel endothelial cell migration; signal transduction; response to organic cyclic substance; germ cell development; negative regulation of positive chemotaxis; response to radiation; negative regulation of angiogenesis; positive regulation of angiogenesis; response to mechanical stimulus; response to hypoxia; response to glucose stimulus; response to activity; angiogenesis; blood coagulation; leukocyte migration
NCBI Summary:	The protein encoded by this gene is an antagonist of angiopoietin 1 (ANGPT1) and endothelial TEK tyrosine kinase (TIE-2, TEK). The encoded protein disrupts the vascular remodeling ability of ANGPT1 and may induce endothelial cell apoptosis. Three transcript variants encoding three different isoforms have been found for this gene. [provided by RefSeq, Jul 2008]
UniProt Code:	O35462
NCBI GenInfo Identifier:	169646754
NCBI Gene ID:	285
NCBI Accession:	NP_001112360.1
UniProt Secondary Accession:	O35462,O35608, O35462,
UniProt Related Accession:	O15123
Molecular Weight:
NCBI Full Name:	angiopoietin-2 isoform c
NCBI Synonym Full Names:	angiopoietin 2
NCBI Official Symbol:	ANGPT2
NCBI Official Synonym Symbols:	ANG2; AGPT2
NCBI Protein Information:	angiopoietin-2
UniProt Protein Name:	Angiopoietin-2
UniProt Gene Name:	ANGPT2
UniProt Entry Name:	ANGP2_HUMAN

Step	Procedure
1.	Set standard, test sample and control (zero) wells on the pre-coated plate respectively, and then, record their positions. It is recommended to measure each standard and sample in duplicate. Wash plate 2 times before adding standard, sample and control (zero) wells!
2.	Aliquot 0.1ml standard solutions into the standard wells.
3.	Add 0.1 ml of Sample / Standard dilution buffer into the control (zero) well.
4.	Add 0.1 ml of properly diluted sample ( Human serum, plasma, tissue homogenates and other biological fluids.) into test sample wells.
5.	Seal the plate with a cover and incubate at 37°C for 90 min.
6.	Remove the cover and discard the plate content, clap the plate on the absorbent filter papers or other absorbent material. Do NOT let the wells completely dry at any time. Wash plate X2.
7.	Add 0.1 ml of Biotin- detection antibody working solution into the above wells (standard, test sample & zero wells). Add the solution at the bottom of each well without touching the side wall.
8.	Seal the plate with a cover and incubate at 37°C for 60 min.
9.	Remove the cover, and wash plate 3 times with Wash buffer. Let wash buffer rest in wells for 1 min between each wash.
10.	Add 0.1 ml of SABC working solution into each well, cover the plate and incubate at 37°C for 30 min.
11.	Remove the cover and wash plate 5 times with Wash buffer, and each time let the wash buffer stay in the wells for 1-2 min.
12.	Add 90 µL of TMB substrate into each well, cover the plate and incubate at 37°C in dark within 10-20 min. (Note: This incubation time is for reference use only, the optimal time should be determined by end user.) And the shades of blue can be seen in the first 3-4 wells (with most concentrated standard solutions), the other wells show no obvious color.
13.	Add 50 µL of Stop solution into each well and mix thoroughly. The color changes into yellow immediately.
14.	Read the O.D. absorbance at 450 nm in a microplate reader immediately after adding the stop solution.

When carrying out an ELISA assay it is important to prepare your samples in order to achieve the best possible results. Below we have a list of procedures for the preparation of samples for different sample types.

Sample Type	Protocol
Serum:	If using serum separator tubes, allow samples to clot for 30 minutes at room temperature. Centrifuge for 10 minutes at 1,000x g. Collect the serum fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles. If serum separator tubes are not being used, allow samples to clotovernight at 2-8°C. Centrifuge for 10 minutes at 1,000x g. Removeserum and assay promptly or aliquot and store the samples at-80°C. Avoid multiple freeze-thaw cycles.
Plasma:	Collect plasma using EDTA or heparin as an anti-coagulant. Centrifuge samples at 4°C for 15 mins at 1000 × g within 30 mins of collection. Collect the plasma fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles.Note: Over haemolysed samples are not suitable for use with this kit.
Urine & Cerebrospinal Fluid:	Collect the urine (mid-stream) in a sterile container, centrifuge for 20 mins at 2000-3000 rpm. Remove supernatant and assay immediately. If any precipitation is detected, repeat the centrifugation step. A similar protocol can be used for cerebrospinal fluid.
Cell Culture Supernatant:	Collect the cell culture media by pipette, followed by centrifugation at 4°C for 20 mins at 1500 rpm. Collect the clear supernatant and assay immediately.
Cell Lysates:	Solubilize cells in lysis buffer and allow to sit on ice for 30 minutes. Centrifuge tubes at 14,000 x g for 5 minutes to remove insoluble material. Aliquot the supernatant into a new tube and discard the remaining whole cell extract. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20°C.
Tissue Homogenates:	The preparation of tissue homogenates will vary depending upon tissue type. Rinse tissue with 1X PBS to remove excess blood & homogenizein 20ml of 1X PBS (including protease inhibitors) and store overnight at ≤ -20°C. Two freeze-thaw cycles are required to break the cell membranes. To further disrupt the cell membranes you can sonicate the samples. Centrifuge homogenates for 5 mins at 5000xg. Remove the supernatant and assay immediately or aliquot and store at -20°C or-80°C.
Tissue Lysates:	Rinse tissue with PBS, cut into 1-2 mm pieces, and homogenize with a tissue homogenizer in PBS. Add an equal volume of RIPA buffer containing protease inhibitors and lyse tissues at room temperature for 30 minutes with gentle agitation. Centrifuge to remove debris. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20 °C.
Breast Milk:	Collect milk samples and centrifuge at 10,000 x g for 60 min at 4°C. Aliquot the supernatant and assay. For long term use, store samples at -80°C. Minimize freeze/thaw cycles.