Rat C-JUN ELISA Kit (RTFI00665)

Product Name:	Rat C-JUN ELISA Kit
Product Code:	RTFI00665
Size:	96 Assays
Target:	Rat c-jun
Alias:	c-jun, V-jun avian sarcoma virus 17 oncogene homolog, Transcription factor AP-1, p39, Activator protein 1, AP1, Proto-oncogene c-Jun
Reactivity:	Rat
Detection Method:	Sandwich ELISA, Double Antibody
Sensitivity:	0.938ng/ml
Range:	1.563-100ng/ml
Storage:	4°C for 6 months
Note:	For Research Use Only

Recovery:

Matrices listed below were spiked with certain level of Rat c-jun and the recovery rates were calculated by comparing the measured value to the expected amount of Rat c-jun in samples.

Matrix	Recovery range(%)	Average(%)
serum(n=5)	89-102	95
EDTA plasma(n=5)	85-99	95
UFH plasma(n=5)	87-101	96

Linearity:

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Rat c-jun and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample	1:2	1:4	1:8
serum(n=5)	97-105%	92-104%	90-105%
EDTA plasma(n=5)	91-98%	89-101%	82-97%
UFH plasma(n=5)	95-100%	80-94%	90-100%

Intra-Assay:

CV <8%

Inter-Assay:

CV <10%

Uniprot:

Q9R237

UniProt Protein Function:	JIP1: a member of the JNK-interacting protein group of scaffold proteins that selectively mediates JNK signaling by aggregating specific components of the MAPK cascade. Required for JNK activation in response to excitotoxic stress. Causes inhibition of JNK-regulated activity by retaining JNK in the cytoplasm and by inhibiting the JNK phosphorylation of c-Jun. May also participate in ApoER2-specific reelin signaling. Directly or indirectly regulates GLUT2 gene expression and beta-cell function. Appears to have a role in cell signaling in mature and developing nerve terminals. May function as a regulator of vesicle transport, through interations with the JNK-signaling components and motor proteins.
UniProt Protein Details:	Protein type:Adaptor/scaffold Cellular Component: endoplasmic reticulum membrane; neuron projection; membrane; axon; perinuclear region of cytoplasm; cytoplasm; mitochondrial membrane; dendrite; synapse; nucleus; cytosol Molecular Function:identical protein binding; JUN kinase binding; protein binding; MAP-kinase scaffold activity; mitogen-activated protein kinase kinase binding; kinesin binding; mitogen-activated protein kinase kinase kinase binding; protein kinase binding Biological Process: vesicle-mediated transport; negative regulation of JNK cascade; negative regulation of JNK activity; positive regulation of signal transduction; regulation of transcription, DNA-dependent; signal transduction; regulation of JNK cascade; JUN phosphorylation; negative regulation of apoptosis
NCBI Summary:	may play a role in the SAPK mediated stress-induced cellular responses [RGD, Feb 2006]
UniProt Code:	Q9R237
NCBI GenInfo Identifier:	87130877
NCBI Gene ID:	116457
NCBI Accession:	ABD24062.1
UniProt Secondary Accession:	Q9R237,O88979, Q9R1H8, Q9WVI5, Q9WVI6,
UniProt Related Accession:	Q9R237
Molecular Weight:	78,356 Da
NCBI Full Name:	JIP1 protein
NCBI Synonym Full Names:	mitogen-activated protein kinase 8 interacting protein 1
NCBI Official Symbol:	Mapk8ip1
NCBI Official Synonym Symbols:	JIP1; Jip-1; Mapk8ip
NCBI Protein Information:	C-Jun-amino-terminal kinase-interacting protein 1; IB-1; JIP-1-related protein; JNK MAP kinase scaffold protein 1; JNK-interacting protein 1; JRP; islet-brain-1; mitogen activated protein kinase 8 interacting protein; mitogen-activated protein kinase 8-interacting protein 1
UniProt Protein Name:	C-Jun-amino-terminal kinase-interacting protein 1
UniProt Synonym Protein Names:	Islet-brain-1; IB-1; JIP-1-related protein; JRP; JNK MAP kinase scaffold protein 1; Mitogen-activated protein kinase 8-interacting protein 1
UniProt Gene Name:	Mapk8ip1
UniProt Entry Name:	JIP1_RAT

Step	Procedure
1.	Set standard, test sample and control (zero) wells on the pre-coated plate respectively, and then, record their positions. It is recommended to measure each standard and sample in duplicate. Wash plate 2 times before adding standard, sample and control (zero) wells!
2.	Aliquot 0.1ml standard solutions into the standard wells.
3.	Add 0.1 ml of Sample / Standard dilution buffer into the control (zero) well.
4.	Add 0.1 ml of properly diluted sample ( Human serum, plasma, tissue homogenates and other biological fluids.) into test sample wells.
5.	Seal the plate with a cover and incubate at 37°C for 90 min.
6.	Remove the cover and discard the plate content, clap the plate on the absorbent filter papers or other absorbent material. Do NOT let the wells completely dry at any time. Wash plate X2.
7.	Add 0.1 ml of Biotin- detection antibody working solution into the above wells (standard, test sample & zero wells). Add the solution at the bottom of each well without touching the side wall.
8.	Seal the plate with a cover and incubate at 37°C for 60 min.
9.	Remove the cover, and wash plate 3 times with Wash buffer. Let wash buffer rest in wells for 1 min between each wash.
10.	Add 0.1 ml of SABC working solution into each well, cover the plate and incubate at 37°C for 30 min.
11.	Remove the cover and wash plate 5 times with Wash buffer, and each time let the wash buffer stay in the wells for 1-2 min.
12.	Add 90 µL of TMB substrate into each well, cover the plate and incubate at 37°C in dark within 10-20 min. (Note: This incubation time is for reference use only, the optimal time should be determined by end user.) And the shades of blue can be seen in the first 3-4 wells (with most concentrated standard solutions), the other wells show no obvious color.
13.	Add 50 µL of Stop solution into each well and mix thoroughly. The color changes into yellow immediately.
14.	Read the O.D. absorbance at 450 nm in a microplate reader immediately after adding the stop solution.

When carrying out an ELISA assay it is important to prepare your samples in order to achieve the best possible results. Below we have a list of procedures for the preparation of samples for different sample types.

Sample Type	Protocol
Serum:	If using serum separator tubes, allow samples to clot for 30 minutes at room temperature. Centrifuge for 10 minutes at 1,000x g. Collect the serum fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles. If serum separator tubes are not being used, allow samples to clotovernight at 2-8°C. Centrifuge for 10 minutes at 1,000x g. Removeserum and assay promptly or aliquot and store the samples at-80°C. Avoid multiple freeze-thaw cycles.
Plasma:	Collect plasma using EDTA or heparin as an anti-coagulant. Centrifuge samples at 4°C for 15 mins at 1000 × g within 30 mins of collection. Collect the plasma fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles.Note: Over haemolysed samples are not suitable for use with this kit.
Urine & Cerebrospinal Fluid:	Collect the urine (mid-stream) in a sterile container, centrifuge for 20 mins at 2000-3000 rpm. Remove supernatant and assay immediately. If any precipitation is detected, repeat the centrifugation step. A similar protocol can be used for cerebrospinal fluid.
Cell Culture Supernatant:	Collect the cell culture media by pipette, followed by centrifugation at 4°C for 20 mins at 1500 rpm. Collect the clear supernatant and assay immediately.
Cell Lysates:	Solubilize cells in lysis buffer and allow to sit on ice for 30 minutes. Centrifuge tubes at 14,000 x g for 5 minutes to remove insoluble material. Aliquot the supernatant into a new tube and discard the remaining whole cell extract. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20°C.
Tissue Homogenates:	The preparation of tissue homogenates will vary depending upon tissue type. Rinse tissue with 1X PBS to remove excess blood & homogenizein 20ml of 1X PBS (including protease inhibitors) and store overnight at ≤ -20°C. Two freeze-thaw cycles are required to break the cell membranes. To further disrupt the cell membranes you can sonicate the samples. Centrifuge homogenates for 5 mins at 5000xg. Remove the supernatant and assay immediately or aliquot and store at -20°C or-80°C.
Tissue Lysates:	Rinse tissue with PBS, cut into 1-2 mm pieces, and homogenize with a tissue homogenizer in PBS. Add an equal volume of RIPA buffer containing protease inhibitors and lyse tissues at room temperature for 30 minutes with gentle agitation. Centrifuge to remove debris. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20 °C.
Breast Milk:	Collect milk samples and centrifuge at 10,000 x g for 60 min at 4°C. Aliquot the supernatant and assay. For long term use, store samples at -80°C. Minimize freeze/thaw cycles.